xTool S1 Tumbler Engraving Settings & Rotary Attachment: A 6-Step Checklist for Buying Teams
- Who this checklist is for
- Step 1: Prep your workspace before you touch the machine
- Step 2: Install the rotary attachment correctly
- Step 3: Dial in tumbler engraving settings for stainless steel
- Step 4: Test, record, repeat
- Step 5: Set up your wood engraving workflow
- Step 6: Batch, check, and box
- Notes and common mistakes
Who this checklist is for
If you're the person who got handed the new xTool S1 and told to "make it work for the company event," this is for you. I'm not a maker. I'm an office administrator who manages about $45,000 in annual vendor spend for a 150-person company. When our marketing team decided they wanted 40 custom tumblers and a stack of engraved wood plaques for a client appreciation event, the S1 landed on my desk with a one-line email: "Can you figure this out by Friday?"
Here's what I wish I'd had on day one. Six steps. About two hours total, assuming you don't make the same mistakes I did.
Step 1: Prep your workspace before you touch the machine
I skipped this and paid for it. The S1 needs ventilation—not optional, not "if you feel like it." I set mine up in a conference room with a window cracked open. Bad idea. After twenty minutes of engraving acrylic, the whole floor smelled like burnt plastic. My facilities manager wasn't thrilled.
What you actually need:
- A space with an exhaust fan or window you can open fully (I ended up moving mine near the loading dock)
- A sturdy table—the S1 with the enclosure weighs around 50 lbs and you don't want it wobbling
- Fire extinguisher within arm's reach (don't laugh, it's a laser)
- A dedicated "test only" scrap pile. I keep a plastic bin labeled exactly that—saved me from wasting good materials more than once
Also, set up your xTool Creative Space (XCS) software before the machine arrives. The registration process needs a firmware update that took me 40 minutes on our office Wi-Fi. Do this when you're not already under deadline pressure.
Step 2: Install the rotary attachment correctly
The xTool S1 rotary attachment is the piece that lets you engrave curved surfaces—tumblers, bottles, that sort of thing. The manual is decent, but here's the part it glosses over: alignment is everything.
Here's the sequence:
- Remove the honeycomb panel from the bed. It's heavier than it looks.
- Mount the rotary's two support wheels onto the S1's base rails. The left side has a tension knob—loosen it before sliding the unit on.
- Slide the drive wheels to roughly where your tumbler will sit. Don't tighten them yet.
- Place your tumbler in the rotary. Adjust the wheel spacing so the tumbler sits level—not nose-up, not nose-down. A 1/8" tilt is enough to burn unevenly.
- Set the focus. The S1's autofocus won't work with the rotary, so you'll manually adjust the laser head height. Use the little acrylic focus tool that came in the box. If you lost it (I did), measure 18mm from the laser lens to the top of your tumbler.
Red flag: if the rotary wheels squeak or the tumbler wobbles as it spins, stop. You'll get uneven engravings that look terrible. Readjust the wheel spacing and try again.
An office colleague of mine said, "Just eyeball it." I did. Wasted six $12 tumblers before I got the alignment right. Now I keep the focus tool taped to the side of the machine.
Step 3: Dial in tumbler engraving settings for stainless steel
Here's the deal-breaker most people don't realize: the S1 is a diode laser. It engraves beautifully on coated stainless steel—think powder-coated Yetis or those matte-finish RTIC cups. Bare stainless steel needs a marking spray (I use LaserBond, about $20 a can) or you'll get a barely-visible ghost line.
Starting settings for a powder-coated 20oz tumbler with the 40W module:
- Power: 55%
- Speed: 180mm/s
- Lines per cm: 50
- Passes: 1
For bare stainless with marking spray:
- Power: 70%
- Speed: 100mm/s
- Lines per cm: 60
- Passes: 2
These are ballpark numbers—every coating is different. The bottom line: run a test grid first. I use a 3x3 grid of 1-inch squares with varying power (40%, 50%, 60%) and speed (100, 150, 200 mm/s) on a scrap piece of the same material. Takes 10 minutes. Saves you from burning the company logo upside down on $30 cups.
For the xtool s1 tumbler engraving settings on tapered tumblers (the ones that aren't straight cylinders), you'll need to adjust the rotary's wheel height to keep the surface parallel to the laser. Trust me—the first time I skipped this, the bottom half of the logo was twice as dark as the top.
Step 4: Test, record, repeat
I keep a notebook—actual paper, not a spreadsheet—next to the machine. Every time I run a new material or tumbler brand, I write down the settings and draw a little sketch of how it turned out. Sounds low-tech. Works better than trying to remember whether "speed 150" was the one that looked good or the one that melted the coating.
My notes from last quarter:
"Yeti 20oz (matte black) — 55% / 180 / 50 LPC. Clean lines, no char.
Generic Amazon tumbler (glossy) — same settings burned too deep. Drop to 45% power.
Stainless with marking spray — 70% / 100 / 60 LPC / 2 passes. Good contrast."
You'll build your own reference list pretty quick. I also photograph every test piece with my phone and keep them in an album labeled "laser settings." Future-you will thank present-you.
Step 5: Set up your wood engraving workflow
How to engrave into wood with the S1 is honestly the easiest part—wood is forgiving. The tricky bit is consistency when you're doing a batch.
My process for a run of 20 wood plaques (we use 1/4" birch plywood from the local lumber yard, about $3 per 12x12 sheet):
- Cut all blanks to size first. I use the S1's cutting settings at 100% power, 8mm/s, 3 passes for 1/4" birch. Measure twice—I cut six pieces at 5" instead of 6" because I didn't check my file units. That was a $18 mistake.
- Engrave with the 20W module: 65% power, 200mm/s, 45 lines per cm, 1 pass. This gives a nice deep etch without burning through the veneer.
- Mask the wood before engraving with transfer tape if you want clean edges. I didn't believe this mattered until I compared a masked piece to an unmasked one. The difference is night and day—no scorch marks around the edges.
Communication failure alert: I once told our designer "standard plaque size" and she sent artwork sized for 8x10. Our blanks were 6x8. Nothing fit. We both said "standard." We meant different things. Now I send dimensions in inches and millimeters, plus a screenshot of the actual blank with a ruler in the photo. Sounds excessive. Costs way less than re-doing 20 plaques.
Step 6: Batch, check, and box
Once you've got your settings locked in, batch processing is straightforward. Here's my routine for a 40-tumbler order:
- Run 5 at a time (rotary makes loading/unloading slow—about 3 minutes per piece for engraving plus setup)
- Inspect each one under the shop light before pulling it off the rotary. Look for uneven burn, alignment drift, or "double lines" (a sign the tumbler shifted mid-engrave)
- Wipe with a microfiber cloth and package immediately. Tumbler dust gets everywhere and looks unprofessional
Total time for 40 tumblers: about 4 hours including setup, test runs, and packaging. Not bad for what would've cost roughly $600-800 from a custom merch vendor (based on quotes I pulled in January 2025—verify current pricing).
Notes and common mistakes
Don't skip the test grid. I know it feels slow. A ruined batch feels slower.
You'll need marking spray for bare stainless. The S1 won't engrave it without it. Order the spray before your first metal project. The 40W module handles coated metals fine, but bare steel is a different story.
Ventilation isn't optional. The S1's enclosure helps, but you still need airflow. I learned this the hard way—see Step 1.
Keep a settings journal. Paper or digital, doesn't matter. But write it down. Your memory for "was it 50% or 55%?" is worse than you think.
Buy a few extra blanks. Whatever quantity you need, order 15% more. I've never had a batch where every single piece came out perfect. Having spares on hand turns a mini-crisis into a 5-minute fix.
The bottom line: the S1 is a solid machine for small-batch branded merch. It's not a production-floor workhorse—you're not going to run 500 tumblers a day on this thing. But for a 20-to-50 piece run of company gifts or client swag? It's a no-brainer once you've dialed in your settings and built a rhythm.
And if your marketing team asks for "just one more batch" next quarter, you'll actually be able to say yes without spending your weekend hunched over a rotary attachment.